UPVC Replacement Door Handles
The handles on your doors are worn out with time and require to be replaced. It is essential to keep the same dimensions as the old handles when replacing them.
The three measurements to check are the top screw's position as well as the key hole and lever sizes. Use the size guide to help you.
Inline Lever/Lever
A lever handle is a contemporary door handle designed to work with new or replacement doors. This style of handle is available in a variety of designs and finishes. A number of manufacturers make this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The uPVC/Composite door handles are made of robust materials and are suitable for multi point lock doors which require a robust design. The handles are inline and operate from the same spindle and screw fixings so they are easily installed on doors made of uPVC/Composite, either new or old.
The handle can be adjusted and angled to fit the needs of all users. The handle has been endurance tested to 200,000 cycles, this helps to ensure the quality of the finish and performance of the handle over time. The sprung lever is adjustable to fit a broad range of locks. This is especially useful in doors with smaller door frames where the cylinder is further back. A shorter lever is a good choice for doors that have latches that can be activated by the thumb turn inside.
Lever Pad
The lever pad upvc handle is different from the lever handles that are found on most doors. These handle types are either operated by a single spindle or by two spindles, either inline or offset. They are typically employed on UPVC doors with double glazing and come in a range of finishes and variations.
The handles are available in various finishes, including White Chrome and Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, thereby giving the handle a high degree of durability and performance for the intended use.
All UPVC lever pads for handles come with a spindle, screws, and can be fitted on the uPVC door. The 211mm backplate fixation centres allow for a bigger handle, which is typically an advantage when replacing an old or damaged multi-point door lock mechanism. These levers for handles are also spring-loaded, which solves the issue of handles hanging out of the horizontal position when they are not in use.
When choosing the replacement UPVC handle and spindle, it is essential to match the dimensions of the PZ on both the multipoint lock and the uPVC door. This measurement may also be called 'handle centre or cylinder centre'. It is important for matching the correct handles.
Once you have the correct PZ size, you'll have to ensure that the lever pads and push pads are a appropriate shape to accommodate the American with Disabilities Act (ADA) compatible handles you need for your doors. These are typically square or round with an internal lever, and an external push pad.
The majority of UPVC lever pads we sell are sprung, meaning that they will return to their horizontal position after not in use, instead of hanging out and possibly sticking in the frame. This stops draughts from entering the property. The majority of UPVC lever pad style handles are available in left and right handed models which allows them to be placed on either side of the doors.
door handle repairs bath are commonly found on uPVC doors, but can also be used on other types of doors. The cylinder lock is operated by a key which unlocks the cylinder case. The case is then able to reveal pins that can be aligned with the pins in the lock and allow them to turn the revolving camera, thereby opening the door. Euro Cylinders can be fitted with up to six pins with both internal and external doors generally having different levels of security.
The choice of cylinder is vital. It is based on the amount of use your doors and handles receive. For example, external doors require a more secure cylinder while internal doors can be secured using the standard cylinder. In addition, some cylinders have extra features which can enhance security further, such as anti-drill or anti-bump properties.
A euro cylinder must be measured accurately to ensure that it is the correct size for your door. The cylinder should be measured from the hole for fixing screws in the middle to each end of the cylinder including the thumb turn if you have one. It is recommended to do this while the lock is in place, but if this is not feasible, you can take it off and take it off to measure. A cylinder that is protruding beyond the handle and escutcheon might be susceptible to attacks like snapping locks, therefore it is crucial to make sure it's not too long.
The design of the latest cylinders includes anti-drilling and bump resistance features. These are designed to reduce the risk of attack by forcing the cylinder rotate in the opposite direction. This can help to deflect attacks and ensure your door is secure.
Certain cylinders are made to withstand snapping. This is a common occurrence on cylinders. A specific tool is used to break the break line of the lock and the front of the cylinder is snapped off. This is a faster and simpler method to gain access than through the use of a multipoint locking system. It also leaves less evidence of the break-in which can make it difficult to prove insurance claims.
Spring Cassette
This spring cassette sits in the base of the door handle backplate, supplying a spring-loaded solution that returns the multipoint lock handles back to their normal position after usage. These handles used to have no spring and would droop when the locking mechanism was disconnected. This simple feature is among the best ways to correct this, and is a great way to prevent your upvc doors from getting stuck in an open or closed position, as these aren't always easy to close manually.
These spring cassettes are specially designed for use with multipoint locks that are sprung, they will not fit non-sprung multipoint handles. You must have a bespoke hole cut into your backplate to allow these to fit (please see image for technical diagram). They are a replacement for existing damaged or missing cassettes inside the backplate of the door handle for various kinds of uPVC doors. They are available as one unit. They have a square-cut out that is able to accommodate an 8mm shaft.
These spring cassettes offer an excellent value solution to the problem of door handles that are sagging. These spring cassettes are simple to install and will increase the lifespan of your uPVC door. Contact us for more information on our wide range of uPVC accessories and spares. We are always happy to provide professional advice and assistance you.